Exfo RTU 310-310G IP Services Test Head User Manual

User GuideRTU-310/310G IP Services Test HeadRTU-310/310G

Certification Informationx RTU-310/310GEuropean Union (CE) InformationElectronic test and measurement equipment is subject to the EMC Directive in the

Creating and Starting a Test Case88 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test Cases2. For addi

Creating and Starting a Test CaseEthernet and Fibre Channel Application 89Ethernet RFC 2544 Test CaseEthernet RFC 2544 Test CaseRFC 2544: Allows Ether

Creating and Starting a Test Case90 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet RFC 2544 Test CaseTo create an RFC 2544 test case:1. Test configur

Creating and Starting a Test CaseEthernet and Fibre Channel Application 91Ethernet RFC 2544 Test Case2. Port configuration:2a. RTU-310Select the port

Creating and Starting a Test Case92 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet RFC 2544 Test Case3. Optical configuration for Ethernet 10G interf

Creating and Starting a Test CaseEthernet and Fibre Channel Application 93Ethernet RFC 2544 Test Case5. Traffic stream configuration5a. For IPv4, sele

Creating and Starting a Test Case94 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet RFC 2544 Test Case6. For additional configuration parameters, refe

Creating and Starting a Test CaseEthernet and Fibre Channel Application 95Ethernet BERT Test CaseEthernet BERT Test CaseAllows Ethernet unframed and L

Creating and Starting a Test Case96 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet BERT Test CaseTo create a BERT test case:1. Test configuration:1a.

Creating and Starting a Test CaseEthernet and Fibre Channel Application 97Ethernet BERT Test Case2c. For Electrical RJ-45, if required, select the Eth

Certification InformationEthernet Test Module xiCE Declaration of Conformity Application of Council Directives: 2006/95/EC - The Low Voltage Dir

Creating and Starting a Test Case98 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet BERT Test Case4. Framing configuration:4a. Select the test framing

Creating and Starting a Test CaseEthernet and Fibre Channel Application 99Ethernet BERT Test Case4b. For Ethernet Unframed, select the Enable Sync che

Creating and Starting a Test Case100 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet BERT Test Case5. Traffic stream configuration:Only Frame Size and

Creating and Starting a Test CaseEthernet and Fibre Channel Application 101Ethernet BERT Test Case5g. Enter the Maximum Rate (%), the default setting

Creating and Starting a Test Case102 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet Frame Analyzer Test CaseEthernet Frame Analyzer Test CaseAllows E

Creating and Starting a Test CaseEthernet and Fibre Channel Application 103Ethernet Frame Analyzer Test CaseTo create a Frame Analyzer test case:1. Te

Creating and Starting a Test Case104 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet Frame Analyzer Test Case2. Port configuration:2a. Select the port

Creating and Starting a Test CaseEthernet and Fibre Channel Application 105Ethernet Frame Analyzer Test Case3. Optical configuration for Ethernet 10G

Creating and Starting a Test Case106 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet Frame Analyzer Test Case4c. Select the PBB-TE check box to enable

Creating and Starting a Test CaseEthernet and Fibre Channel Application 107Ethernet Frame Analyzer Test Case5. Traffic stream configuration:5a. Select

Creating and Starting a Test Case108 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet Frame Analyzer Test Case5f. Set the VLAN parameters when required

Creating and Starting a Test CaseEthernet and Fibre Channel Application 109Ethernet Smart Loopback Test CaseEthernet Smart Loopback Test CaseAllows tr

Creating and Starting a Test Case110 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet Smart Loopback Test Case1f. For RTU-310select the port number by

Creating and Starting a Test CaseEthernet and Fibre Channel Application 111Ethernet Smart Loopback Test Case2. Optical configuration for Ethernet 10G

Creating and Starting a Test Case112 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet Smart Loopback Test Case3. Framing configuration:3a. Set the Auto

Creating and Starting a Test CaseEthernet and Fibre Channel Application 113Ethernet TCP Throughput Test CaseEthernet TCP Throughput Test CaseTCP Throu

Creating and Starting a Test Case114 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet TCP Throughput Test Case2. Port configuration:Port 1 (RTU-310 onl

Creating and Starting a Test CaseEthernet and Fibre Channel Application 115Ethernet TCP Throughput Test Case4. Click the TCP Throughput tab and TCP Th

Creating and Starting a Test Case116 FTB-8500 Series and FTB-8120NGE/8130NGEFibre Channel BERT Test CaseFibre Channel BERT Test CaseTypical Fibre Chan

Creating and Starting a Test CaseEthernet and Fibre Channel Application 117Fibre Channel BERT Test Case2. Port configuration:2a. For RTU-310select the

Ethernet Test Module 11 Introducing the RTU-310/310GThe RTU-310/310G is a powerful 24/7 network testing solution for IPTV and Ethernet services.Featur

Creating and Starting a Test Case118 FTB-8500 Series and FTB-8120NGE/8130NGEFibre Channel BERT Test Case3. Framing selection:3a. Select the test frami

Creating and Starting a Test CaseEthernet and Fibre Channel Application 119Fibre Channel BERT Test Case4. Framing configuration (available with FC Fra

Ethernet and Fibre Channel Application 1216 Summary TabsThe summary tabs allow to configure the test parameters and to view the test status and result

Summary Tabs122 FTB-8500 Series and FTB-8120NGE/8130NGETest Summar yTest Status Start Time: Indicates the date and time the test has been started. Th

Summary TabsEthernet and Fibre Channel Application 123Test Summary SAM Test Status: Indicates the EtherSAM test status message.Test Status Desciption

Summary Tabs124 FTB-8500 Series and FTB-8120NGE/8130NGETest Summar y RFC 2544: Indicates the status of the running RFC 2544 test. This setting is onl

Summary TabsEthernet and Fibre Channel Application 125Test SummaryClock Configuration Clock Mode indicates the clock mode selected during the test se

Summary Tabs126 FTB-8500 Series and FTB-8120NGE/8130NGETest Summar yTimer ConfigurationAllows to automatically start and/or stop a test case at a give

Summary TabsEthernet and Fibre Channel Application 127Test Summary On/Off button allows enabling the test timer. An error message is displayed and th

Introducing the RTU-310/310G2 RTU-310/310GFeatures Boot using USB drive RTU health diagnostics Remote restart NTP server support with daylight sav

Summary Tabs128 FTB-8500 Series and FTB-8120NGE/8130NGEAlarm SummaryAlarm SummaryClick TEST, Summary, and Alarm.The Alarm summary tab gives access to

Summary TabsEthernet and Fibre Channel Application 129Alarm Summary TestGlobal: Indicates the presence of any alarms/errors related to the test such

Summary Tabs130 FTB-8500 Series and FTB-8120NGE/8130NGEAlarm Summary Higher Layer Protocol (Ethernet): Indicates the presence of any error related to

Summary TabsEthernet and Fibre Channel Application 131Test LoggerTest LoggerClick TEST, Summary, and Alarm.The Test Logger lists the test status/event

Summary Tabs132 FTB-8500 Series and FTB-8120NGE/8130NGETest L oggerLogger TableAn event is automatically listed in the logger and saved on the hard dr

Ethernet and Fibre Channel Application 1337Port TabsThe port tabs allow to configure different port parameters and to view the port analysis.Note: The

Port Tabs134 FTB-8500 Series and FTB-8120NGE/8130NGEElectrical TXElectrical TXClick TEST, Port, and Electrical TX.ConfigurationEthernet port crossover

Port TabsEthernet and Fibre Channel Application 135Electrical TXFrequencyNote: Frequency offset generation is not available for 10Base-T test and when

Port Tabs136 FTB-8500 Series and FTB-8120NGE/8130NGEElectrical RXElectrical RXClick TEST, Port, and Electrical RX.Alarm AnalysisFrequency: The frequen

Port TabsEthernet and Fibre Channel Application 137Electrical RXFrequency AnalysisNote: Frequency Analysis is not available for 10Base-T test. Freque

Introducing the RTU-310/310GEthernet Test Module 3ModelsModelsThe RTU-310 is equipped with two electrical 10/1000/1000 Mbps Ethernet port and two opti

Port Tabs138 FTB-8500 Series and FTB-8120NGE/8130NGEOptical TXOptical TXClick TEST, Port, and Optical TX.Signal Analysis Output Presence: Indicates t

Port TabsEthernet and Fibre Channel Application 139Optical TXFrequencyNote: Frequency offset is not available when Through Mode (RTU-310 only) is sele

Port Tabs140 FTB-8500 Series and FTB-8120NGE/8130NGEOptical RXOptical RXClick TEST, Port, and Optical RX.Signal Analysis Power Level (dBm): Indicates

Port TabsEthernet and Fibre Channel Application 141Optical RXFrequency AnalysisFrequency (bps): Indicates the frequency of the input signal in bps.Fre

Port Tabs142 FTB-8500 Series and FTB-8120NGE/8130NGEInterface Setup (Ethernet)Interface Setup (Ethernet)Note: For Fibre Channel test case, see Interfa

Port TabsEthernet and Fibre Channel Application 143Interface Setup (Ethernet) Auto-Negotiation (Not available on RTU-310G)The Auto-Negotiation should

Port Tabs144 FTB-8500 Series and FTB-8120NGE/8130NGEInterface Setup (Ethernet) Flow ControlAvailable with Frame Analyzer, RFC 2544, and TCP Throughpu

Port TabsEthernet and Fibre Channel Application 145Interface Setup (Ethernet)Status Link: A green Link LED indicates that there is a link at the inpu

Port Tabs146 FTB-8500 Series and FTB-8120NGE/8130NGEInterface Setup (Fibre Channel)Interface Setup (Fibre Channel)Note: For Ethernet test case, see In

Port TabsEthernet and Fibre Channel Application 147Interface Setup (Fibre Channel)LoginThe capability to log in is available only if a successful link

Introducing the RTU-310/310G4 RTU-310/310GModelsRTU-310G AC version DC version

Port Tabs148 FTB-8500 Series and FTB-8120NGE/8130NGEInterface Setup (Fibre Channel) Port Status: Indicates the status of the port login process. Poss

Port TabsEthernet and Fibre Channel Application 149Interface Setup (Fibre Channel)Buffer-to-Buffer Flow Control Enable: The Enable check box is force

Port Tabs150 FTB-8500 Series and FTB-8120NGE/8130NGENetworkNetworkNote: Network is only available with Framed Layer 2 and when Through Mode (RTU-310)

Port TabsEthernet and Fibre Channel Application 151NetworkSource MAC ConfigurationMAC Address: A default and unique Media Access Control (MAC) address

Port Tabs152 FTB-8500 Series and FTB-8120NGE/8130NGENetworkSource IP ConfigurationFor IPv4: Automatic IP Address: Allows to dynamically obtain an IP

Port TabsEthernet and Fibre Channel Application 153NetworkFor IPv6: Displays the Link-Local IPv6 Address, Global IPv6 Address, and Default Gateway Ad

Port Tabs154 FTB-8500 Series and FTB-8120NGE/8130NGEAdvanced Auto-Neg. TXAdvanced Auto-Neg. TXNote: Advanced auto-negotiation is not available with th

Port TabsEthernet and Fibre Channel Application 155Advanced Auto-Neg. TXConfigurationThe Speed, Duplex, and Flow Control can be modified only when the

Port Tabs156 FTB-8500 Series and FTB-8120NGE/8130NGEAdvanced Auto-Neg. TXNote: Only None is available for BERT analyzer test.Note: Flow Control should

Port TabsEthernet and Fibre Channel Application 157Advanced Auto-Neg. TXAuto-Neg. Fault Register Fault Type: Allows the generation of a fault during

Introducing the RTU-310/310GEthernet Test Module 5OptionOptionOptical Transceivers (SFP) Option DescriptionRTU-8580 Software key that enables the 1000

Port Tabs158 FTB-8500 Series and FTB-8120NGE/8130NGEAdvanced Auto-Neg. TXNegotiate ButtonThe Negotiate button allows starting the auto-negotiation pro

Port TabsEthernet and Fibre Channel Application 159Advanced Auto-Neg. RXAdvanced Auto-Neg. RXNote: Advanced auto-negotiation is not available with the

Port Tabs160 FTB-8500 Series and FTB-8120NGE/8130NGEAdvanced Auto-Neg. RX Duplex: Indicates the negotiated duplex mode. Possible values are Half, and

Ethernet and Fibre Channel Application 1618 Stream Generation TabsNote: Stream generation is not available with Smart Loopback and TCP Throughput (RTU

Stream Generation Tabs162 FTB-8500 Series and FTB-8120NGE/8130NGEOverviewOverviewThe Overview tab allows configuration and activation of up to 10 stre

Stream Generation TabsEthernet and Fibre Channel Application 163OverviewNote: The Individual stream can be enabled/disabled even when the test is star

Stream Generation Tabs164 FTB-8500 Series and FTB-8120NGE/8130NGEOverview Copy Stream buttonTo copy the stream configuration to one or several stream

Stream Generation TabsEthernet and Fibre Channel Application 165OverviewFor BERT and RFC 2544 No: Indicates the stream identification number. Only on

Stream Generation Tabs166 FTB-8500 Series and FTB-8120NGE/8130NGEStream ConfigurationStream ConfigurationPress TEST, Stream Gen, and Stream Config.Str

Stream Generation TabsEthernet and Fibre Channel Application 167Stream ConfigurationFor Video: Video Codec: Choices are SDTV (MPEG-2), HDTV (MPEG-2),

Introducing the RTU-310/310G6 RTU-310/310GOptical Transceivers (XFP)Optical Transceivers (XFP)Option DescriptionFTB-85900 850 nm short-wave optics (10

Stream Generation Tabs168 FTB-8500 Series and FTB-8120NGE/8130NGEStream Configuration Transport: Select the transport traffic type (layer 4). Choices

Stream Generation TabsEthernet and Fibre Channel Application 169Stream ConfigurationThe following table lists each component that may affect the minim

Stream Generation Tabs170 FTB-8500 Series and FTB-8120NGE/8130NGEStream Configuration For BERT test:For Framed Layer 1, only the Data Link (Ethernet)

Stream Generation TabsEthernet and Fibre Channel Application 171Stream ConfigurationThe following table lists each component that may affect the minim

Stream Generation Tabs172 FTB-8500 Series and FTB-8120NGE/8130NGEStream ConfigurationTraffic Shaping Transmit Mode: Allows the selection of the Trans

Stream Generation TabsEthernet and Fibre Channel Application 173Stream Configuration TX Rate: Enter the transmission rate. The available stream trans

Stream Generation Tabs174 FTB-8500 Series and FTB-8120NGE/8130NGEStream ConfigurationFor Ramp Traffic ShapingNote: Available for Stream 1 with Ramp an

Stream Generation TabsEthernet and Fibre Channel Application 175PBB-TEPBB-TEAllows configuration of PBB-TE streams including B-MAC (source and destina

Stream Generation Tabs176 FTB-8500 Series and FTB-8120NGE/8130NGEPBB-TEDestination B-MAC Address: Enter the destination Backbone MAC address for the

Stream Generation TabsEthernet and Fibre Channel Application 177MACMACNote: Only available with Framed Layer 2.Click TEST, Stream Gen, and MAC.Stream

Introducing the RTU-310/310GEthernet Test Module 7ConventionsConventionsBefore using the product described in this manual, you should understand the f

Stream Generation Tabs178 FTB-8500 Series and FTB-8120NGE/8130NGEMACSourceMAC Address: Indicates the MAC address of the selected stream.Note: The sour

Stream Generation TabsEthernet and Fibre Channel Application 179MACVLANNote: For RFC 2544 test, VLAN is only configurable through the Network on page

Stream Generation Tabs180 FTB-8500 Series and FTB-8120NGE/8130NGEMPLSMPLSAllows MPLS configuration of streams with up to two layers of MPLS labels, CO

Stream Generation TabsEthernet and Fibre Channel Application 181MPLSMPLS Configuration Stacked Headers: Allows the activation of up to two MPLS heade

Stream Generation Tabs182 FTB-8500 Series and FTB-8120NGE/8130NGEIP/UDP/TCPIP/UDP/TCPNote: Only available when the network stream configuration is set

Stream Generation TabsEthernet and Fibre Channel Application 183IP/UDP/TCPFor IPv6:Displays the Link-Local IPv6 Address, Global IPv6 Address, and Defa

Stream Generation Tabs184 FTB-8500 Series and FTB-8120NGE/8130NGEIP/UDP/TCP IP TOS/DS for IPv4 or Traffic Class (TOS/DS) for IPv6Enter the user defin

Stream Generation TabsEthernet and Fibre Channel Application 185PayloadPayloadNote: Not available with BERT test.Not available when the Stream Tag (Fr

Stream Generation Tabs186 FTB-8500 Series and FTB-8120NGE/8130NGEFrame Configuration (Fibre Channel)Frame Configuration (Fibre Channel)Note: Frame Con

Stream Generation TabsEthernet and Fibre Channel Application 187Frame Configuration (Fibre Channel) EOF: The EOF represents the End Of Frame delimite

ii RTU-310/310GCopyright © 2007–2012 EXFO Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or tra

Stream Generation Tabs188 FTB-8500 Series and FTB-8120NGE/8130NGEFrame Configuration (Fibre Channel)Frame Parameter Size: Allows the selection of the

Stream Generation TabsEthernet and Fibre Channel Application 189Frame Configuration (Fibre Channel)FC HeaderNote: FC Header is only available with Fib

Stream Generation Tabs190 FTB-8500 Series and FTB-8120NGE/8130NGEFrame Configuration (Fibre Channel) D_ID: The Destination Identifier specifies the l

Stream Generation TabsEthernet and Fibre Channel Application 191Frame Configuration (Fibre Channel) CS_CTL: The Class Specific Control field contains

Stream Generation Tabs192 FTB-8500 Series and FTB-8120NGE/8130NGEFrame Configuration (Fibre Channel) F_CTL: The Frame Control contains control inform

Stream Generation TabsEthernet and Fibre Channel Application 193Frame Configuration (Fibre Channel)9Retransmitted Sequence0 = Original Sequence transm

Stream Generation Tabs194 FTB-8500 Series and FTB-8120NGE/8130NGEFrame Configuration (Fibre Channel) SEQ_ID: The Sequence Identifier specifies the se

Ethernet and Fibre Channel Application 1959 Stream Analyzer TabsNote: Stream analyzer is only available with Frame Analyzer test. Stream analyzer tabs

Stream Analyzer Tabs196 FTB-8500 Series and FTB-8120NGE/8130NGEOverview Latency Cur. (ms) indicates for each stream the current measured round trip l

Stream Analyzer TabsEthernet and Fibre Channel Application 197StreamStreamClick TEST, Stream Analyzer, and Stream.Note: Available with Frame Analyzer

Ethernet Test Module 92 Safety InformationLaser Safety WarningsWARNINGDo not install or terminate fibres while a laser source is active. Never look di

Stream Analyzer Tabs198 FTB-8500 Series and FTB-8120NGE/8130NGEStreamThroughputThe throughput is measured for each stream on all valid frames (valid T

Ethernet and Fibre Channel Application 19910 Traffic Analyzer TabsNote: The available Traffic Analyzer tabs depend on which test path is activated.Tes

Traffic Analyzer Tabs200 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet TXEthernet TXNote: Available with BERT test with Framed Layer 1 and Framed La

Traffic Analyzer TabsEthernet and Fibre Channel Application 201Ethernet TXPHY Error Injection Type: The following error is available with both manual

Traffic Analyzer Tabs202 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet TX Rate: Click the Rate field to select the rate for the automated error. Ch

Traffic Analyzer TabsEthernet and Fibre Channel Application 203Ethernet RXEthernet RXClick TEST, Traffic Analyzer, and Eth. RX.ConfigurationOversize M

Traffic Analyzer Tabs204 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet RXErrors Analysis Block (10Gig-E): The number of frames received with an err

Traffic Analyzer TabsEthernet and Fibre Channel Application 205Ethernet RXThe following errors are only available with Half Duplex mode. Not available

Traffic Analyzer Tabs206 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet StatisticsEthernet StatisticsClick TEST, Traffic Analyzer, and Eth. Stats.Val

Traffic Analyzer TabsEthernet and Fibre Channel Application 207Ethernet StatisticsFrame Size Count: Gives the count of each received frame size (vali

Safety Information10 RTU-310/310GInstallation Instruction WarningsInstallation Instruction WarningsCAUTIONNo user serviceable parts are contained insi

Traffic Analyzer Tabs208 FTB-8500 Series and FTB-8120NGE/8130NGEPBB-TEPBB-TEAnalyzes streams with PBB-TE data traffic.Note: The PBB-TE check box has b

Traffic Analyzer TabsEthernet and Fibre Channel Application 209PBB-TEPPB-TE Frame Size Count: Gives the count of each received PBB-TE frame size (val

Traffic Analyzer Tabs210 FTB-8500 Series and FTB-8120NGE/8130NGEHigher LayersHigher LayersClick TEST, Traffic Analyzer, and Higher Layers.Higher Layer

Traffic Analyzer TabsEthernet and Fibre Channel Application 211Higher LayersMPLSNote: MPLS is only availabe when enabled from the test setup.Frame Cou

Traffic Analyzer Tabs212 FTB-8500 Series and FTB-8120NGE/8130NGEFlow ControlFlow ControlClick TEST, Traffic Analyzer, and Flow Control.Note: One Quant

Traffic Analyzer TabsEthernet and Fibre Channel Application 213Flow ControlNote: When entering a value in μs/ns it will be rounded to the closest mult

Traffic Analyzer Tabs214 FTB-8500 Series and FTB-8120NGE/8130NGEFlow ControlStatistics Pause Time: Indicates the total number of pause time received

Traffic Analyzer TabsEthernet and Fibre Channel Application 215Traffic FiltersTraffic FiltersAllows gathering statistics according to the programmed f

Traffic Analyzer Tabs216 FTB-8500 Series and FTB-8120NGE/8130NGETraffic FiltersFilter ConfigurationAllows to configure the criteria for the selected f

Traffic Analyzer TabsEthernet and Fibre Channel Application 217Traffic FiltersIPv6aIPv6 Destination AddressIPv6 Source AddressIPv6 Flow LabelIPv6 Next

Safety InformationEthernet Test Module 11Installation Instruction WarningsIMPORTANTUnauthorized modifications to this equipment shall void the user’s

Traffic Analyzer Tabs218 FTB-8500 Series and FTB-8120NGE/8130NGETraffic Filters ValueAllows entering the value associated to the selected filter. See

Traffic Analyzer TabsEthernet and Fibre Channel Application 219Traffic FiltersFrame CountIndicates the number of frame matching the configured filter’

Traffic Analyzer Tabs220 FTB-8500 Series and FTB-8120NGE/8130NGETraffic Filter ConfigurationTraffic Filter ConfigurationAllows gathering statistics ac

Traffic Analyzer TabsEthernet and Fibre Channel Application 221Traffic Filter ConfigurationFilter: Allows the selection of the filter to be used. The

Traffic Analyzer Tabs222 FTB-8500 Series and FTB-8120NGE/8130NGETraffic Filter StatsTraffic Filter StatsAllows gathering statistics according to the p

Traffic Analyzer TabsEthernet and Fibre Channel Application 223Traffic Filter StatsThroughputIndicates throughput statistics of frame matching the con

Traffic Analyzer Tabs224 FTB-8500 Series and FTB-8120NGE/8130NGECaptureCaptureCapture is a troubleshooting tool used to capture received data traffic

Traffic Analyzer TabsEthernet and Fibre Channel Application 225Capture Frame LengthAllows to select the length of the frame that will be saved in the

Traffic Analyzer Tabs226 FTB-8500 Series and FTB-8120NGE/8130NGECaptureTrigger Trigger Type: Allows to define the trigger source criterion that will

Traffic Analyzer TabsEthernet and Fibre Channel Application 227Capture Trigger Position: Allows the selection of the triggered frame position within

Traffic Analyzer Tabs228 FTB-8500 Series and FTB-8120NGE/8130NGECapture Capture button: Allows to start/stop the data capture. The test must be runni

Traffic Analyzer TabsEthernet and Fibre Channel Application 229GraphGraphGives the graph showing the test measurement results.Click TEST, Traffic Anal

Traffic Analyzer Tabs230 FTB-8500 Series and FTB-8120NGE/8130NGEFC TXFC TXClick TEST, Traffic Analyzer, and FC TX.Alarm Generation Type: The followin

Traffic Analyzer TabsEthernet and Fibre Channel Application 231FC TXPHY Error Injection Type: The following errors are available with both manual and

Traffic Analyzer Tabs232 FTB-8500 Series and FTB-8120NGE/8130NGEFC TXFC Error InjectionNote: FC Error Injection is available with Framed Layer 2 only.

Traffic Analyzer TabsEthernet and Fibre Channel Application 233FC RXFC RXClickTEST, Traffic Analyzer, and FC RX.Alarm Analysis Link Down: Indicates t

Traffic Analyzer Tabs234 FTB-8500 Series and FTB-8120NGE/8130NGEFC RXError Analysis Symbol (FC 1x, and 2x): A Symbol error is declared when an invali

Traffic Analyzer TabsEthernet and Fibre Channel Application 235FC LatencyFC LatencyNote: Available with FC Framed Layer 1 and FC Framed Layer 2 only.C

Traffic Analyzer Tabs236 FTB-8500 Series and FTB-8120NGE/8130NGEFC LatencyLatency MeasurementsRound Trip Delay  Maximum: Indicates the maximum time t

Traffic Analyzer TabsEthernet and Fibre Channel Application 237FC StatisticsFC StatisticsNote: Available with FC Framed Layer 1 and FC Framed Layer 2

Ethernet Test Module 133 Getting StartedThis chapter covers the description of the RTU-310/310G unit, the physical installation, all connections, LEDs

Ethernet and Fibre Channel Application 23911 WIS TabsNote: The WIS tabs are only available with 10 GigE WAN transceiver mode. Not available with Smart

WIS Tabs240 FTB-8500 Series and FTB-8120NGE/8130NGEWIS TXAlarm GenerationNote: Alarm generation is available with BERT test only. Type: The following

WIS TabsEthernet and Fibre Channel Application 241WIS TX ERDI-PCD (Enhanced RDI - Path Connectivity Defect): Generates a “110” pattern for bits 5, 6

WIS Tabs242 FTB-8500 Series and FTB-8120NGE/8130NGEWIS TXPath Signal Label (C2)The C2 byte is allocated to indicate the content of the STS SPE, includ

WIS TabsEthernet and Fibre Channel Application 243WIS RXWIS RXClick TEST, WIS, and WIS RX.Error Analysis B1 (BIP-8, Bit-Interleave Parity - 8 bits):

WIS Tabs244 FTB-8500 Series and FTB-8120NGE/8130NGEWIS RX REI-L (Remote Error Indicator - Line): The REI-L error is declared when bits 5 through 8 of

WIS TabsEthernet and Fibre Channel Application 245WIS RX LOP-P (Loss Of Pointer - Path): For non-concatenated payloads, the LOP-P alarm indicates tha

WIS Tabs246 FTB-8500 Series and FTB-8120NGE/8130NGEWIS OH RXWIS OH RXAllows verification of the transport overhead information received.Click TEST, WI

WIS TabsEthernet and Fibre Channel Application 247WIS OH RXSection OverheadNote: Monitor the first timeslot only. A1 and A2: Framing. The value shoul

Getting Started14 RTU-310/310GSHUT DOWN / RESTART ButtonSHUT DOWN / RESTART ButtonThe SHUT DOWN/RESTART button is used to either shut down or restart

WIS Tabs248 FTB-8500 Series and FTB-8120NGE/8130NGEWIS OH RXPath Overhead J11: Trace. B31: BIP-8 C2: Signal Label G1: Status F2: User Channel H4

Ethernet and Fibre Channel Application 24912 IPTV TabsNote: The IPTV tabs are available with Frame Analyzer application type on the RTU-310 module onl

IPTV Tabs250 FTB-8500 Series and FTB-8120NGE/8130NGEIPTV Testing with the RTU-310IPTV Testing with the RTU-310The RTU-310 module provides the capabili

IPTV TabsEthernet and Fibre Channel Application 251IPTV Testing with the RTU-310The RTU-310 module equipped with the IPTV option can be used at differ

IPTV Tabs252 FTB-8500 Series and FTB-8120NGE/8130NGEDiscoveryDiscoveryThe Discovery page allows the auto-discovery function to automatically scans the

IPTV TabsEthernet and Fibre Channel Application 253DiscoveryThe status of each stream, active or inactive, is visually presented as follow: Active: S

IPTV Tabs254 FTB-8500 Series and FTB-8120NGE/8130NGEDiscoveryStream MonitoringThe Add function adds the streams to the stream monitoring list in the o

IPTV TabsEthernet and Fibre Channel Application 255DiscoverySelection OptionsNote: Selection Options is not available when Auto-Add is selected. Only

IPTV Tabs256 FTB-8500 Series and FTB-8120NGE/8130NGEOverviewOverviewThe Overview tab provides a summary of the key statistics that can be used as firs

IPTV TabsEthernet and Fibre Channel Application 257OverviewTo organize the streams key statistics presentation, the Overview page supports several sor

Getting StartedEthernet Test Module 15RTU-310/310G LEDsRTU-310/310G LEDsVGA PortThe VGA port is used to connect a monitor to access the EX-Vu applicat

IPTV Tabs258 FTB-8500 Series and FTB-8120NGE/8130NGEOverviewColumn Description Join Status: Indicates the join status for each multicast stream only.

IPTV TabsEthernet and Fibre Channel Application 259Overview DF (ms): The Delay Factor (DF) provides a measure of the maximum packet delay variation o

IPTV Tabs260 FTB-8500 Series and FTB-8120NGE/8130NGEOverviewStream StatusThe status of each stream, active or inactive, is visually presented as follo

IPTV TabsEthernet and Fibre Channel Application 261OverviewAdd ButtonThe Add button adds streams to the stream monitoring list. The Add button is disa

IPTV Tabs262 FTB-8500 Series and FTB-8120NGE/8130NGEOverview Deselect All deselects all the streams in the list.Manual Entry, when selected, adds one

IPTV TabsEthernet and Fibre Channel Application 263OverviewDelete ButtonThe Delete button removes streams from the stream monitoring list. Streams can

IPTV Tabs264 FTB-8500 Series and FTB-8120NGE/8130NGEOverviewManual Entry, when selected, removes one specific stream. Destination IP Address: Enter t

IPTV TabsEthernet and Fibre Channel Application 265OverviewIGMP ButtonThe IGMP button facilitates the management of the IGMP capabilities associated t

IPTV Tabs266 FTB-8500 Series and FTB-8120NGE/8130NGEOverviewStreams can be sorted using Stream Name, Dest IP address, Auto Join, or Join Status. When

IPTV TabsEthernet and Fibre Channel Application 267Overview Disable Auto-Join / Leave Button: This button toggles from Disable Auto-Join to Leave whe

Getting Started16 RTU-310/310GInstalling the RTU-310/310G in a RackInstalling the RTU-310/310G in a RackTo install the RTU-310/310G in a rack:1. Fix t

IPTV Tabs268 FTB-8500 Series and FTB-8120NGE/8130NGEOverview Join Status: The Join-Status is represented by the following icons. Icons become grayed

IPTV TabsEthernet and Fibre Channel Application 269OverviewAlias MapAllows the creation of a table establishing the relation between a destination IP

IPTV Tabs270 FTB-8500 Series and FTB-8120NGE/8130NGEOverview Alias Add allows a new alias map entry to the IPTV alias map list. Use the Stream Name

IPTV TabsEthernet and Fibre Channel Application 271MDI/TR 101 290MDI/TR 101 290The MDI/TR 101 290 page contains the detailed statistics associated to

IPTV Tabs272 FTB-8500 Series and FTB-8120NGE/8130NGEMDI/TR 101 290StreamThe Select Stream pop up allows the selection of a stream to see its statistic

IPTV TabsEthernet and Fibre Channel Application 273MDI/TR 101 290MDI (Media Delivery Index)The use of the Media Delivery Index as a testing metric pro

IPTV Tabs274 FTB-8500 Series and FTB-8120NGE/8130NGEMDI/TR 101 290Note: The Delay Factor (and associated Virtual Buffer Size) value behavior can chang

IPTV TabsEthernet and Fibre Channel Application 275MDI/TR 101 290TR 101 290The TR 101 290 determines the integrity of the MPEG-2 Transport Stream acro

IPTV Tabs276 FTB-8500 Series and FTB-8120NGE/8130NGEMDI/TR 101 290PMT Error2: Indicates that any of the following conditions appear during a 1 second

IPTV TabsEthernet and Fibre Channel Application 277MDI/TR 101 290TR 101 290 ThresholdTR 101 290 Threshold parameters apply to all streams. PCR Jitter

Getting StartedEthernet Test Module 17Installing the RTU-310/310G in a Rack2. Place the unit in the rack at the desired height.3. Fix the unit in plac

IPTV Tabs278 FTB-8500 Series and FTB-8120NGE/8130NGEIGMPIGMPThe IGMP functions associated to all streams currently support Version 2 of the IGMP stand

IPTV TabsEthernet and Fibre Channel Application 279IGMPTo access the IGMP tab, click TEST, IPTV, and IGMP.Multicast GroupStreamThe Select Stream pop u

IPTV Tabs280 FTB-8500 Series and FTB-8120NGE/8130NGEIGMPSelect a stream from the list by clicking on it, or perform a search in the stream list by ent

IPTV TabsEthernet and Fibre Channel Application 281IGMPEnable Auto-Join, available when the test is stopped, enables the IGMP auto-join function. The

IPTV Tabs282 FTB-8500 Series and FTB-8120NGE/8130NGEIGMPSummary (All Multicast Groups)The following gives statistics on all monitored multicast stream

IPTV TabsEthernet and Fibre Channel Application 283IGMPConfiguration IGMP Version: Indicates the supported IGMP version which is IGMP version 2. Note

IPTV Tabs284 FTB-8500 Series and FTB-8120NGE/8130NGEStream InformationStream InformationThe Stream Info tab completes the information provided by the

IPTV TabsEthernet and Fibre Channel Application 285Stream InformationStreamThe Select Stream pop up allows the selection of a stream to see informatio

IPTV Tabs286 FTB-8500 Series and FTB-8120NGE/8130NGEStream InformationDuration Start Time: Indicates the time at which the stream monitoring has star

IPTV TabsEthernet and Fibre Channel Application 287Stream InformationIP Rate (Mbps): Indicates the number of megabits received in the last second (Mb

ContentsEthernet Test Module iiiContentsCertification Information ...

Getting Started18 RTU-310/310GConnecting the PowerConnecting the PowerThe RTU-310/310G is available with either an AC or DC integrated power supply.No

Ethernet and Fibre Channel Application 28913 Pattern TabsNote: The Pattern tabs are only available with BERT test.TabAvailable withPageEthernet Fibre

Pattern Tabs290 FTB-8500 Series and FTB-8120NGE/8130NGEPattern TXPattern TXClick TEST, and Pattern.Configuration Test Pattern: Select the test patter

Pattern TabsEthernet and Fibre Channel Application 291Pattern TX Invert: The generated test pattern will be inverted if the Invert check box is selec

Pattern Tabs292 FTB-8500 Series and FTB-8120NGE/8130NGEPattern TXError InjectionAllows selection and configuration of a manual or automated pattern er

Pattern TabsEthernet and Fibre Channel Application 293Pattern RXPattern RXClick TEST, and Pattern.ConfigurationNote: See Configuration on page 290 for

Pattern Tabs294 FTB-8500 Series and FTB-8120NGE/8130NGEPattern RXError AnalysisBit Error: A Bit Error indicates that there are logic errors in the bit

Ethernet and Fibre Channel Application 29514 RFC 2544 TabsNote: The RFC 2544 tabs are only available with RFC 2544 test.Note: The RFC 2544 measurement

RFC 2544 Tabs296 FTB-8500 Series and FTB-8120NGE/8130NGEGlobal ConfigurationGlobal ConfigurationClick TEST, RFC 2544, and Global.Configuration Frame

RFC 2544 TabsEthernet and Fibre Channel Application 297Global Configuration Frame Size (Bytes): RFC 2544 gives predefined frame size distribution val

Getting StartedEthernet Test Module 19Connecting the PowerTo connect the RTU-310/310G to a DC power source:1. Remove the two Phillips flat screws, and

RFC 2544 Tabs298 FTB-8500 Series and FTB-8120NGE/8130NGEGlobal ConfigurationTest Procedure Test: Enables the RFC 2544 sub-tests to be performed. Choi

RFC 2544 TabsEthernet and Fibre Channel Application 299ThroughputThroughputThe objective of this test is to find the throughput of the device under te

RFC 2544 Tabs300 FTB-8500 Series and FTB-8120NGE/8130NGEThroughputConfiguration Test Time (MM:SS): Enter the test time value. Possible values are 1 s

RFC 2544 TabsEthernet and Fibre Channel Application 301Throughput Maximum Rate: TX-to-RX/P1-to-P2/P2-to-P1/Local to Remote/Remote to Local: Select th

RFC 2544 Tabs302 FTB-8500 Series and FTB-8120NGE/8130NGEThroughputResults Test State--: Indicates that the test has not run yet.In Progress: Indicate

RFC 2544 TabsEthernet and Fibre Channel Application 303Throughput Throughput Results Frame Size: Indicates the frame sizes used for the test. Up to

RFC 2544 Tabs304 FTB-8500 Series and FTB-8120NGE/8130NGEBack-to-BackBack-to-BackThe objective of this test is to find the maximum number of frames tha

RFC 2544 TabsEthernet and Fibre Channel Application 305Back-to-BackConfiguration Max. time worth of frame (MM:SS): Choices are 1 to 5 seconds. The de

RFC 2544 Tabs306 FTB-8500 Series and FTB-8120NGE/8130NGEBack-to-BackResults Test State--: Indicates that the test has not run yet.In Progress: Indica

RFC 2544 TabsEthernet and Fibre Channel Application 307Back-to-Back Current Trial: Indicates the current trial number. Unit: Select the throughput r

Getting Started20 RTU-310/310GConnecting the Power5. Using 14-16 AWG copper insulated wires and the supplied lug, insert the two stripped wires into t

RFC 2544 Tabs308 FTB-8500 Series and FTB-8120NGE/8130NGEFrame LossFrame LossThe objective of this test is to find the percentage of frames that are lo

RFC 2544 TabsEthernet and Fibre Channel Application 309Frame Loss Test Granularity (%): Select the test granularity. The test granularity is the perc

RFC 2544 Tabs310 FTB-8500 Series and FTB-8120NGE/8130NGEFrame LossResults Test State--: Indicates that the test has not run yet.In Progress: Indicate

RFC 2544 TabsEthernet and Fibre Channel Application 311Frame Loss Frame Loss Results Frame Size: Indicates the frame sizes used for the test. Up to

RFC 2544 Tabs312 FTB-8500 Series and FTB-8120NGE/8130NGELatencyLatencyThe objective of this test is to find the time required for the sent frame to go

RFC 2544 TabsEthernet and Fibre Channel Application 313LatencyConfiguration Test Time (MM:SS): Select the test time value. Choices are 1 second to 2

RFC 2544 Tabs314 FTB-8500 Series and FTB-8120NGE/8130NGELatency Set All To: Enter a value in the Set All To and click OK to apply the value to all fr

RFC 2544 TabsEthernet and Fibre Channel Application 315LatencyResults Test State--: Indicates that the test has not run yet.In Progress: Indicates th

RFC 2544 Tabs316 FTB-8500 Series and FTB-8120NGE/8130NGELatency Latency ResultsNote: The “--” indicates that the result is not available because the

RFC 2544 TabsEthernet and Fibre Channel Application 317GraphGraphGives the graph showing the Throughput, Back-to-Back, Frame Loss, or Latency measurem

Getting StartedEthernet Test Module 21Turning the Unit On7. Connect the other end of wires to the DC power source.8. To add a redundant DC source on t

RFC 2544 Tabs318 FTB-8500 Series and FTB-8120NGE/8130NGEGraph Unit: Select the result unit. Choices are: Layer/Displayed Step/ModeLayer (Throughput

RFC 2544 TabsEthernet and Fibre Channel Application 319Graph Displayed Results: Select the displayed results mode: Current, Minimum, Maximum, or Aver

Ethernet and Fibre Channel Application 32115 EtherSAM TabsNote: The EtherSAM tabs are only available with EtherSAM (Y.1564) test. The EtherSAM tabs ar

EtherSAM Tabs322 FTB-8500 Series and FTB-8120NGE/8130NGEOverview (Configuration)Overview (Configuration)The Overview tab allows the activation of up t

EtherSAM TabsEthernet and Fibre Channel Application 323Overview (Configuration)When the Service Performance Test is enabled, up to 10 services can be

EtherSAM Tabs324 FTB-8500 Series and FTB-8120NGE/8130NGEOverview (Configuration)In the third stage of the test, when the Ramp Traffic Policing Rate ch

EtherSAM TabsEthernet and Fibre Channel Application 325Overview (Configuration)Sub-Tests Duration Service Configuration Test displays the Service Con

EtherSAM Tabs326 FTB-8500 Series and FTB-8120NGE/8130NGEOverview (Configuration)Total TX Rate (%)Note: Only available when the Service Performance Tes

EtherSAM TabsEthernet and Fibre Channel Application 327Services (Configuration)Services (Configuration)Click TEST, EtherSAM Configuration, and Service

Getting Started22 RTU-310/310GConnecting the Test Interface PortsConnecting the Test Interface PortsConnecting the Electrical 10/100/1000 Mbps Etherne

EtherSAM Tabs328 FTB-8500 Series and FTB-8120NGE/8130NGEServices (Configuration) Framing indicates and allows to change the selected framing. The fra

EtherSAM TabsEthernet and Fibre Channel Application 329Services (Configuration) PBB-TE indicates and allows to change the selected frame PBB-TE desti

EtherSAM Tabs330 FTB-8500 Series and FTB-8120NGE/8130NGEServices (Configuration) CIR+EIR sets the best effort allowed traffic for the service. The EI

EtherSAM TabsEthernet and Fibre Channel Application 331Services (Configuration)Performance Criteria Max Jitter allows to set the maximum jitter value

EtherSAM Tabs332 FTB-8500 Series and FTB-8120NGE/8130NGEServices (Configuration)Test ParametersRamp Traffic Policing Rate allows to stress the rate li

EtherSAM TabsEthernet and Fibre Channel Application 333Ramp (Configuration)Ramp (Configuration)Note: The Ramp tab is only available when the ramp test

EtherSAM Tabs334 FTB-8500 Series and FTB-8120NGE/8130NGERamp (Configuration)Step List Step indicates the step number. Up to 10 steps may be configure

EtherSAM TabsEthernet and Fibre Channel Application 335Burst (Configuration)Burst (Configuration)Note: The Burst configuration is only available when

EtherSAM Tabs336 FTB-8500 Series and FTB-8120NGE/8130NGEBurst (Configuration) Burst Frame represents the burst frame ratio in percentage that is equa

EtherSAM TabsEthernet and Fibre Channel Application 337Burst (Configuration)TableNote: Result values are only available for enabled services. Service

Getting StartedEthernet Test Module 23Connecting the Test Interface PortsElectrical Port LEDsLED Status DescriptionLINK/ACT On Ethernet link upOff Eth

EtherSAM Tabs338 FTB-8500 Series and FTB-8120NGE/8130NGEOverview (Results)Overview (Results)Click TEST, EtherSAM Results, and Overview.Global Progress

EtherSAM TabsEthernet and Fibre Channel Application 339Overview (Results) Global Verdict indicates the actual test PA SS or FAIL verdict. A FAIL verd

EtherSAM Tabs340 FTB-8500 Series and FTB-8120NGE/8130NGEOverview (Results) Alarms Link Down: Indicates that the Ethernet connection is down due to a

EtherSAM TabsEthernet and Fibre Channel Application 341Overview (Results) Verdict indicates that the performance metrics (Jitter, Latency, and Frame

EtherSAM Tabs342 FTB-8500 Series and FTB-8120NGE/8130NGEOverview (Results)Service Performance Test OverviewDisplays an overview of the service perform

EtherSAM TabsEthernet and Fibre Channel Application 343Service Configuration Test (Results)Service Configuration Test (Results)Click TEST, EtherSAM Re

EtherSAM Tabs344 FTB-8500 Series and FTB-8120NGE/8130NGEService Configuration Test (Results)Ramp and Burst Tests Table Step, for ramp test, indicates

EtherSAM TabsEthernet and Fibre Channel Application 345Service Configuration Test (Results) Verdict indicates that the performance metrics (Jitter, L

EtherSAM Tabs346 FTB-8500 Series and FTB-8120NGE/8130NGEService Performance Test (Results)Service Performance Test (Results)Click TEST, EtherSAM Resul

EtherSAM TabsEthernet and Fibre Channel Application 347Service Performance Test (Results)Sequence Tracking Out-Of-Sequence (OOS) is declared when a v

Getting Started24 RTU-310/310GConnecting the Test Interface PortsConnecting the Optical 100/1000 Mbps and 10 Gbps Ethernet Test InterfacesThe RTU-310

EtherSAM Tabs348 FTB-8500 Series and FTB-8120NGE/8130NGEService Performance Test (Results)Round Trip LatencyThe round trip latency (delay) is measured

Ethernet and Fibre Channel Application 34916 TCP Throughput TabsNote: The TCP Throughput tabs are only available with TCP Throughput test. Available w

TCP Throughput Tabs350 FTB-8500 Series and FTB-8120NGE/8130NGETCP Throughput ConfigurationClick TEST, TCP Throughput, and TCP Throughput Configuration

TCP Throughput TabsEthernet and Fibre Channel Application 351TCP Throughput Configuration Port: Enter the TCP port number. The default setting is 502

TCP Throughput Tabs352 FTB-8500 Series and FTB-8120NGE/8130NGETCP Throughput ConfigurationTCP Throughput ConfigurationNote: TCP Throughput Configurati

TCP Throughput TabsEthernet and Fibre Channel Application 353TCP Throughput AnalysisTCP Throughput AnalysisNote: Only available on the local unit.Clic

TCP Throughput Tabs354 FTB-8500 Series and FTB-8120NGE/8130NGETCP Throughput Analysis Window SizeLast: Indicates the last TCP window size.Minimum: In

Ethernet and Fibre Channel Application 35517 Advanced TabNote: The available Advanced tab depends on which test path is activated.Service Disruption T

Advanced Tab356 FTB-8500 Series and FTB-8120NGE/8130NGEService Disruption Time (SDT)ConfigurationSelect the criteria that will be used for the SDT mea

Advanced TabEthernet and Fibre Channel Application 357Service Disruption Time (SDT)the Test Period value is set to its maximum value: 300000000 μs). T

Getting StartedEthernet Test Module 25Connecting the Test Interface PortsTo use the optical 100/1000 Mbps Ethernet interface for testing:1. Insert one

Advanced Tab358 FTB-8500 Series and FTB-8120NGE/8130NGEService Disruption Time (SDT) Service Disruption: Indicates the time (in seconds) during which

Ethernet and Fibre Channel Application 35918 Common TabPerformance Monitoring (PM)The Performance Monitoring tab gives error performance events and pa

Common Tab360 FTB-8500 Series and FTB-8120NGE/8130NGEPerformance Monitoring (PM)StandardSelect the desired standard from the list. Choices are:Statist

Common TabEthernet and Fibre Channel Application 361Performance Monitoring (PM) SES (Severely Errored Second)For G.821: Gives the number of seconds w

Common Tab362 FTB-8500 Series and FTB-8120NGE/8130NGEPerformance Monitoring (PM) UAS (Unavailable Second): Gives the count of the seconds correspondi

Ethernet and Fibre Channel Application 36319 Expert Mode TabsNote: The Expert Mode tabs are only available with BERT and RFC 2544 Ethernet tests (not

Expert Mode Tabs364 FTB-8500 Series and FTB-8120NGE/8130NGEExpert Mode (RFC 2544)Expert Mode (RFC 2544)Expert Mode allows the configuration of the thr

Expert Mode TabsEthernet and Fibre Channel Application 365Expert Mode (RFC 2544)Expert Mode StatusGives the verdict, Pass or Fail, of the Throughput,

Expert Mode Tabs366 FTB-8500 Series and FTB-8120NGE/8130NGEThroughput (RFC 2544)Throughput (RFC 2544)Click TEST, Expert Mode, and Throughput. Enable

Expert Mode TabsEthernet and Fibre Channel Application 367Throughput (RFC 2544) Layer: Select the Layer. Choices are Layer 1,2,3, Layer 2,3, and Laye

Getting Started26 RTU-310/310GConnecting the Test Interface Ports2. Carefully connect optical fiber cables to the SFP’s or XFP’s IN and OUT ports.To e

Expert Mode Tabs368 FTB-8500 Series and FTB-8120NGE/8130NGEBack-to-Back (RFC 2544)Back-to-Back (RFC 2544)Click TEST, Expert Mode, and Back-to-Back. E

Expert Mode TabsEthernet and Fibre Channel Application 369Back-to-Back (RFC 2544) Layer: Select the Layer. Choices are Layer 1,2,3, Layer 2,3, and La

Expert Mode Tabs370 FTB-8500 Series and FTB-8120NGE/8130NGEFrame Loss (RFC 2544)Frame Loss (RFC 2544)Click TEST, Expert Mode, and Frame Loss. Enable

Expert Mode TabsEthernet and Fibre Channel Application 371Frame Loss (RFC 2544) Displayed Step: Indicates the last percentage of the speed used for t

Expert Mode Tabs372 FTB-8500 Series and FTB-8120NGE/8130NGELatency (RFC 2544)Latency (RFC 2544)Click TEST, Expert Mode, and Latency. Enable Criteria:

Expert Mode TabsEthernet and Fibre Channel Application 373Latency (RFC 2544) Mode: Select the Mode. Choices are Cut Through and Store and Forward. Th

Expert Mode Tabs374 FTB-8500 Series and FTB-8120NGE/8130NGEExpert Mode (BERT)Expert Mode (BERT)Expert Mode allows the configuration of the thresholds

Expert Mode TabsEthernet and Fibre Channel Application 375Port (BERT)Port (BERT)Click TEST, Expert Mode, and Port.Enable Criteria: Enable Criteria ena

Expert Mode Tabs376 FTB-8500 Series and FTB-8120NGE/8130NGEPort (BERT)FrequencyEnter the minimum and maximum frequency offsets either in ppm or bps ac

Expert Mode TabsEthernet and Fibre Channel Application 377Ethernet (BERT)Ethernet (BERT)Click TEST, Expert Mode, and Ethernet.Enable Criteria: Enable

Getting StartedEthernet Test Module 27Connecting the Test Interface PortsOptical Port LEDs for RTU-310GLED Status DescriptionLASER On An optical signa

Expert Mode Tabs378 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet (BERT)ErrorsEnter the threshold value for each error. Status: Indicates the real-

Expert Mode TabsEthernet and Fibre Channel Application 379Pattern (BERT)Pattern (BERT)Click TEST, Expert Mode, and Pattern.Enable Criteria: Enable Cri

Expert Mode Tabs380 FTB-8500 Series and FTB-8120NGE/8130NGEPattern (BERT)ErrorsEnter the threshold value for Bit Error. Status: Indicates the real-ti

Ethernet Test Module 38120 System TabsThe System tab gives access to tabs containing general functions related to the RTU-310/310G operation.TabAvaila

System Tabs382 RTU-310/310GPreferencesPreferencesClick System, and Preferences/Default Perference.Time Options Time Format: Sets the absolute time fo

System TabsEthernet Test Module 383PreferencesPage Management Reset to Display Default Pages Layout when enabled, resets the page layout to its defau

System Tabs384 RTU-310/310GDefault/Ethernet Test PreferencesDefault/Ethernet Test PreferencesClick Default/System and Preferences/Default Test Prefere

System TabsEthernet Test Module 385Default/Ethernet Test PreferencesInterface ConfigurationNote: The following interface configuration parameters are

System Tabs386 RTU-310/310GIPv6 Test PreferencesIPv6 Test PreferencesClick System and Preferences/IPv6 Test Preferences.Note: The following configurat

System TabsEthernet Test Module 387IPv6 Test Preferences Global IPv6 Address: The Global IPv6 Address (GUA) is used to communicate with on-link neigh

Contentsiv RTU-310/310G5 Creating and Starting a Test Case ...67Introducing the Test Setup

Getting Started28 RTU-310/310GConnecting the Management InterfacesConnecting the Management InterfacesConnecting the Ethernet CRAFT PortConnecting a P

System Tabs388 RTU-310/310GIPv6 Test Preferences Default Gateway Address: The Default Gateway Address is used to forward packets outside the subnet.

System TabsEthernet Test Module 389FC Test PreferencesFC Test PreferencesNote: Not available with RTU-310G.Click System and Preferences/FC Test Prefer

System Tabs390 RTU-310/310GFC Test Preferences Advertised BB_Credit: Advertised BB_Credit is the number of frame buffers that a local port has availa

System TabsEthernet Test Module 391RTU InformationRTU InformationThe RTU Information provides details of the RTU-310/310G hardware and the software in

System Tabs392 RTU-310/310GRTU InformationHardware OptionsProvides hardware information related to the SFP. Available only with RTU-310. The followin

System TabsEthernet Test Module 393RTU SetupRTU SetupClick System and the RTU Setup. LAN InterfaceThe following interface configuration parameters are

System Tabs394 RTU-310/310GRTU Setup Default Gateway: Sets the Default Gateway for the LAN Interface port.If Automatic IP Address is selected, it dis

System TabsEthernet Test Module 395RTU Setup Current Date and Time: Allows the selection of the specific date (YYYY-MM-DD) and time (HH:MM:SS) when t

System Tabs396 RTU-310/310GSoftware OptionsSoftware OptionsAllows the installation of software options. A software option key will be generated by EXF

System TabsEthernet Test Module 397Software OptionsAvailable OptionsThe available software options are listed with the Status indicating what software

Getting StartedEthernet Test Module 29Connecting the Management InterfacesCRAFT Port Embedded LEDsLED Status DescriptionLINK/ACT(Green)On Ethernet lin

System Tabs398 RTU-310/310GSoftware OptionsFeature SK-802-3AH The 802.3ah OAM Protocol is enabled.SK-TCP-THPUT The TCP Throughput measurement applicat

System TabsEthernet Test Module 399Software OptionsFor RTU-310GCategory Name DescriptionInterface SK-ADV-FILTERS Advanced Traffic FilteringSK-ETHERSAM

System Tabs400 RTU-310/310GClock SynchronizationClock SynchronizationNote: Clock Synchronization is only available for Ethernet 10G.Click System and C

System TabsEthernet Test Module 401Clock SynchronizationFor E1: PCM30, PCM30 CRC-4, PCM31, and PCM31 CRC-4. The default setting is PCM30.Alarm Analysi

System Tabs402 RTU-310/310GClock Synchronization Frequency: The Frequency alarm indicates if the received signal rate meets (green) or not (red) the

System TabsEthernet Test Module 403Clock SynchronizationREF OutNote: Ref Output is only available with RTU-310G, the REF OUT signal is automatically e

System Tabs404 RTU-310/310GAlarms & LogAlarms & LogProvides information on the system alarm status and system alarm logger. Click System and A

System TabsEthernet Test Module 405Alarms & Log Fan Failure: Indicates that one of the internal fan’s rotation speed has decreased below 50 perce

Ethernet and Fibre Channel Application 40721 Tools TabsNote: The To ols tabs are only available when a test is created.TabAvailable withPageEthernet F

Getting Started30 RTU-310/310GConnecting the Management InterfacesConnecting the Ethernet LAN PortThe RTU-310/310G LAN interface is designed to provid

Tools Tabs408 FTB-8500 Series and FTB-8120NGE/8130NGEScriptScriptThe scripting tool allows a user to automate test process by creating scripts contain

Tools TabsEthernet and Fibre Channel Application 409ScriptEditLists the content of the current script and allows its edition. Users with writing knowl

Tools Tabs410 FTB-8500 Series and FTB-8120NGE/8130NGEScriptScript ToolsAllows automatic generation of scripts by setting step by step the parameters f

Tools TabsEthernet and Fibre Channel Application 411ScriptNote: However, for RFC 2544, all selected tests (Throughput, Back-to-Back, Frame Loss, and/o

Tools Tabs412 FTB-8500 Series and FTB-8120NGE/8130NGEPing ConfigurationPing ConfigurationThe Ping tool is used to determine if a network device is rea

Tools TabsEthernet and Fibre Channel Application 413Ping Configuration Delay (ms): Available for ping only. Enter the delay between each attempt (PIN

Tools Tabs414 FTB-8500 Series and FTB-8120NGE/8130NGEPing ResultsPing ResultsClick Tools, Ping, in the Tool list, click Ping, and click Result.Note: F

Tools TabsEthernet and Fibre Channel Application 415Ping ResultsTime Out When an ICMPv4/ICMPv6 echo reply was not received within the defined timeout.

Tools Tabs416 FTB-8500 Series and FTB-8120NGE/8130NGEPing ResultsFor IPv4: Replied From: Indicates the IP address of the replier. Bytes: Indicates t

Tools TabsEthernet and Fibre Channel Application 417Trace Route ConfigurationTrace Route ConfigurationTrace Route is used to obtain the list of all ro

Getting StartedEthernet Test Module 31Connecting the Management InterfacesLAN Port Embedded LEDsLED Status DescriptionLINK/ACT(Green)On Ethernet link

Tools Tabs418 FTB-8500 Series and FTB-8120NGE/8130NGETrace Route ResultsTrace Route ResultsClick Tools, Ping, Configuration, in the Tool list, click T

Tools TabsEthernet and Fibre Channel Application 419Trace Route Results Status: Indicates the status of the attempt.Status DescriptionSuccessful Vali

Tools Tabs420 FTB-8500 Series and FTB-8120NGE/8130NGETrace Route Results Replied From: Indicates the IP address of the replier. Time (ms): Indicates

Tools TabsEthernet and Fibre Channel Application 421ENIU ConfigurationENIU ConfigurationAllows supporting the Operation, Administration, and Maintenan

Tools Tabs422 FTB-8500 Series and FTB-8120NGE/8130NGEADC ConfigurationADC ConfigurationNote: The ADC Config tab is only available when ADC is selected

Tools TabsEthernet and Fibre Channel Application 423ADC Configuration ENIU Status: Indicates the ENIU status. Possible statuses are:Valid: The remote

Tools Tabs424 FTB-8500 Series and FTB-8120NGE/8130NGEADC ConfigurationSelected ENIUIndicates the information related to the selected ENIU. MAC Addres

Tools TabsEthernet and Fibre Channel Application 425ADC ConfigurationLoopbackAllows sending a loopback request to the selected ENIU.Note: If the selec

Tools Tabs426 FTB-8500 Series and FTB-8120NGE/8130NGE802.3ah Configuration802.3ah ConfigurationNote: The 802.3ah Config tab is only available when 802

Tools TabsEthernet and Fibre Channel Application 427802.3ah Configuration LoopbackRequest allows the selection of the loopback request to be sent to

Getting Started32 RTU-310/310GSoftware ManagementSoftware ManagementSoftware management functionality ensures that the version of EX-Vu running on the

Tools Tabs428 FTB-8500 Series and FTB-8120NGE/8130NGE802.3ah Statistics802.3ah StatisticsNote: The 802.3ah Stats tab is only available when 802.3ah is

Tools TabsEthernet and Fibre Channel Application 429802.3ah Statistics Parser Action: Bits 0 and 1 of the State byte report the Parser Action.Forward

Tools Tabs430 FTB-8500 Series and FTB-8120NGE/8130NGE802.3ah Statistics OUI: The 24-bit IEEE Organizationally Unique Identifer field identifies the v

Tools TabsEthernet and Fibre Channel Application 431802.3ah Events802.3ah EventsNote: The 802.3ah Events tab is only available when 802.3ah is selecte

Tools Tabs432 FTB-8500 Series and FTB-8120NGE/8130NGE802.3ah Events Threshold. Error Count. Error Running Total. Event Running TotalSymbol Period

Tools TabsEthernet and Fibre Channel Application 433Traffic ScanTraffic ScanThe traffic scan tool provides the capability to discover and monitor VLAN

Tools Tabs434 FTB-8500 Series and FTB-8120NGE/8130NGETraffic ScanLevelAllows the selection of the criteria that will be used to filter the incoming VL

Tools TabsEthernet and Fibre Channel Application 435Traffic ScanLink Rate (Mbps)Indicates the network link rate based on the received frames with a va

Tools Tabs436 FTB-8500 Series and FTB-8120NGE/8130NGETraffic ScanMonitored Frames TableStatistics are gathered for each different traffic flow matchin

Tools TabsEthernet and Fibre Channel Application 437Traffic ScanFor MPLS Mode, the level of MPLS (Unlabeled, 1 Label, 2 Labels), and the values of Lab

Getting StartedEthernet Test Module 33Software ManagementTo match the version of Ex-Vu to the current version of the RTU-310/310G software load:1. Sel

Tools Tabs438 FTB-8500 Series and FTB-8120NGE/8130NGETraffic Scan FiltersThe column’s All/Ignore toggle buttons are used to set the filtering criteri

Tools TabsEthernet and Fibre Channel Application 439Traffic Scan Frame Count indicates for each traffic flow, the number of frames matching the selec

Ethernet Test Module 44122 MaintenanceTo help ensure long, trouble-free operation: Always inspect fiber-optic connectors before using them and clean

Maintenance442 RTU-310/310GRecalibrating the UnitRecalibrating the UnitManufacturing and service center calibrations are based on the ISO/IEC 17025 St

MaintenanceEthernet Test Module 443Replacing FusesReplacing FusesThe RTU-310/310G contains two fuses (T4A, 5 mm x 20 mm (0.197 in x 0.787 in), slow-bl

Maintenance444 RTU-310/310GReplacing Fuses4. Insert the new fuse into the fuse holder.5. Make sure the fuses are placed firmly in the holder prior to

Ethernet Test Module 44523 WarrantyGeneral InformationEXFO Inc. (EXFO) warrants this equipment against defects in material and workmanship for a perio

Warranty446 RTU-310/310GLiabilityLiabilityEXFO shall not be liable for damages resulting from the use of the product, nor shall be responsible for any

WarrantyEthernet Test Module 447Service and RepairsService and RepairsEXFO commits to providing product service and repair for five years following th

Getting Started34 RTU-310/310GSoftware Management2. Click Yes to confirm the downloadThe current RTU-310/310G software load is uninstalled and the oth

Warranty448 RTU-310/310GEXFO Service Centers WorldwideEXFO Service Centers WorldwideIf your product requires servicing, contact your nearest authorize

Ethernet Test Module 44924 TroubleshootingSolving Common ProblemsBefore calling EXFO’s technical support, please read the following common problems th

Troubleshooting450 RTU-310/310GContacting the Technical Support GroupContacting the Technical Support GroupTo obtain after-sales service or technical

TroubleshootingEthernet Test Module 451TransportationTransportationMaintain a temperature range within specifications when transporting the unit. Tran

Ethernet Test Module 453ASpecificationsSpecifications for RTU-310Optical Interfaces100Base-FX 100Base-LX 1000Base-SX 1000Base-LX 1000Base-ZXWavelength

Specifications454 RTU-310/310GSpecifications for RTU-310Electrical Interfaces Transceiver type SFP SFP SFP SFP SFP10Base-T 100Base-T 1000Base-TTX bit

SpecificationsEthernet Test Module 455Specifications for RTU-310Ethernet CablesMinimum Category 3 cable is required for 10Base-T connection while Cate

Specifications456 RTU-310/310GSpecifications for RTU-310 Straight Through Cable (1000 Mbps) Crossover Cable (1000 Mbps)

SpecificationsEthernet Test Module 457Specifications for RTU-310Functional SpecificationsCommunication Interfaces LANPort RJ-45Rates: 10/100 Mbps CR

Getting StartedEthernet Test Module 35Software ManagementTo transfer files to the RTU-310/310G:1. Create a folder on the local drive of the RTU-310/31

Specifications458 RTU-310/310GSpecifications for RTU-310IPTV StatisticsRFC 4445 delivery index Delay factor (current, average, min, max) Media loss

SpecificationsEthernet Test Module 459Specifications for RTU-310Stream Statistics Ethernet Bandwidth utilization IP IP rate (current, average, min

Specifications460 RTU-310/310GSpecifications for RTU-310Additional Features Stream auto discovery Stream alias map Configurable alarm thresholds M

SpecificationsEthernet Test Module 461Specifications for RTU-310General SpecificationsSize (H x W x D) 1U rack-mount chassis (19 and 23 in. rack-mount

Specifications462 RTU-310/310GSpecifications for RTU-310GSpecifications for RTU-310GOptical Interfaces 10GBASE-SW10GBASE-SR10GBASE-LW 10GBASE-LR 10GBA

SpecificationsEthernet Test Module 463Specifications for RTU-310GSynchronization InterfacesDS1/E1 external input clock interfaceEye safety CLASS 1 CLA

Specifications464 RTU-310/310GSpecifications for RTU-310GElectrical InterfacesElectrical Interfaces External clock DS1/E1 and clock outputExternal clo

SpecificationsEthernet Test Module 465Specifications for RTU-310GREF out interfaceParameter ValueTx pulse amplitude 600 mVpp ± 130 mVTransmission freq

Specifications466 RTU-310/310GSpecifications for RTU-310GEthernet CablesMinimum Category 3 cable is required for 10Base-T connection while Category 5

SpecificationsEthernet Test Module 467Specifications for RTU-310G Straight Through Cable (1000 Mbps) Crossover Cable (1000 Mbps)

Specifications468 RTU-310/310GSpecifications for RTU-310GFunctional SpecificationsCommunication Interfaces LANPort RJ-45Rates: 10/100 Mbps CRAFTPort

SpecificationsEthernet Test Module 469Specifications for RTU-310GStream Statistics Ethernet Bandwidth utilization IP IP rate (current, average, mi

Specifications470 RTU-310/310GSpecifications for RTU-310GAdditional Test and Measurement Functions Power measurement Supports optical power measuremen

SpecificationsEthernet Test Module 471Specifications for RTU-310GModule SpecificationsRTU-310G-LAN RTU-310G-WAN RTU-310G-LAN/WANPort One 10 Gigabit Et

Specifications472 RTU-310/310GSpecifications for RTU-310GGeneral SpecificationsCommunication InterfaceLAN port RJ-45Rates: 10/100 Mbit/sCraft port RJ-

Ethernet Test Module 473B Using VNC to access the RTU-310/310GVNC is a graphical desktop sharing software that allows a computer to remotely control a

Using VNC to access the RTU-310/310G474 RTU-310/310GRemote Connection using TightVNCRemote Connection using TightVNCConnect to the RTU-310/310G using

Using VNC to access the RTU-310/310GEthernet Test Module 475Transferring files using TightVNCTransferring files using TightVNCTo transfer files from t

Using VNC to access the RTU-310/310G476 RTU-310/310GTransferring files using TightVNC3. Navigate to the new folder on the RTU-310/310G from the TightV

Using VNC to access the RTU-310/310GEthernet Test Module 477Transferring files using TightVNCTo transfer files from the RTU-310/310G to the local comp

Ethernet and Fibre Channel Application 374 Introducing the Smart User InterfaceTo Start the RTU-310/310G Application:1. Once your RTU-310/310G module

Using VNC to access the RTU-310/310G478 RTU-310/310GTransferring files using TightVNC3. Navigate to the new folder on your machine from the Local Comp

Ethernet Test Module 479CAcronym ListABCD?HelpAAmpereAC Alternating CurrentAMa.m.Ante Meridiem (period between midnight and noon)ANSI American Nationa

Acronym List480 RTU-310/310GEFGHDHCP Dynamic Host Configuration ProtocolEMC Electromagnetic CompatibilityEMS Element Management SystemESD Electrostati

Acronym ListEthernet Test Module 481IKLIC Industry CanadaID IdentificationIECInternational Electrotechnical CommissionIEEE Institute of Electrical &am

Acronym List482 RTU-310/310GMNOPm MeterMAC Media Access ControlMbps Megabit Per SecondMDI Media Delivery Indexmin. minuteMLR Media Loss RateMMF Multi-

Acronym ListEthernet Test Module 483RSPCR Program Clock ReferencePID Packet IdentifierPMp.m.Post Meridiem (period from noon to midnight)PMT Program Ma

Acronym List484 RTU-310/310GTUVTX TransmitUDP User Data ProtocolUI User InterfaceURLUniform Resource LocatorUSA United States of AmericaUSB Universal

Ethernet and Fibre Channel Application 485D Pop-Up WindowsNote: The following Pop-Up windows are available throughout the user interface.Tab PageVLAN

Pop-Up Windows486 FTB-8500 Series and FTB-8120NGE/8130NGEVLAN ConfigurationVLAN Configuration Enable VLAN appears only for EtherSAM service configura

Pop-Up WindowsEthernet and Fibre Channel Application 487PBB-TE Interface configurationPBB-TE Interface configurationThe PBB-TE Interface window allows

ContentsEthernet Test Module v10 Traffic Analyzer Tabs ... 199Ethernet T

Introducing the Smart User Interface38 FTB-8500 Series and FTB-8120NGE/8130NGELoginNote: An error is displayed when the connection to the RTU-310/310G

Pop-Up Windows488 FTB-8500 Series and FTB-8120NGE/8130NGEPBB-TE Interface configuration B-VLAN (Backbone Virtual Local Area Network)ID: Enter the B-V

Pop-Up WindowsEthernet and Fibre Channel Application 489IPv4 ConfigurationIPv4 ConfigurationSourceNote: For EtherSAM Dual Test Set, the source IP addr

Pop-Up Windows490 FTB-8500 Series and FTB-8120NGE/8130NGEIPv4 Configuration Resolve MAC Address: When enabled, will send a request to the network to

Pop-Up WindowsEthernet and Fibre Channel Application 491IPv6 Address ConfigurationIPv6 Address ConfigurationNote: The default IPv6 address parameters

Pop-Up Windows492 FTB-8500 Series and FTB-8120NGE/8130NGEIPv6 Address ConfigurationGlobal IPv6 AddressThe Global IPv6 Address (GUA) is used for global

Pop-Up WindowsEthernet and Fibre Channel Application 493IPv6 Address Configuration Link-Local/Global IPv6 Address StatusMode Status DescriptionStatel

Pop-Up Windows494 FTB-8500 Series and FTB-8120NGE/8130NGEIPv6 Address ConfigurationDefault Gateway AddressThe Default Gateway Address is used to forwa

Pop-Up WindowsEthernet and Fibre Channel Application 495IPv6 Address ConfigurationDestination IPv6 AddressNote: Destination IPv6 address is only avail

Pop-Up Windows496 FTB-8500 Series and FTB-8120NGE/8130NGECopy Service Network ConfigurationCopy Service Network ConfigurationThis pop-up window is onl

Pop-Up WindowsEthernet and Fibre Channel Application 497Service Profile ConfigurationService Profile ConfigurationThis pop-up window is only available

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 39Main WindowMain WindowApplication nameMinimizeHelpExitTa bsTa b( s)Ta b’

Pop-Up Windows498 FTB-8500 Series and FTB-8120NGE/8130NGEFraming ConfigurationFraming ConfigurationThis pop-up window is only available with EtherSAM

Pop-Up WindowsEthernet and Fibre Channel Application 499Frame Size ConfigurationFrame Size ConfigurationThis pop-up window is only available with Ethe

Pop-Up Windows500 FTB-8500 Series and FTB-8120NGE/8130NGEFrame Size ConfigurationThe following table lists each component that may affect the minimum

Pop-Up WindowsEthernet and Fibre Channel Application 501Frame Format ConfigurationFrame Format ConfigurationThis pop-up window is only available with

Pop-Up Windows502 FTB-8500 Series and FTB-8120NGE/8130NGEMAC ConfigurationMAC ConfigurationThis pop-up window is only available with EtherSAM (Y.1564)

Pop-Up WindowsEthernet and Fibre Channel Application 503MPLS ConfigurationMPLS ConfigurationThis pop-up window is only available with EtherSAM (Y.1564

Pop-Up Windows504 FTB-8500 Series and FTB-8120NGE/8130NGEMPLS Configuration COS/EXP (Class Of Service / Experimental): Select the class of service. T

Pop-Up WindowsEthernet and Fibre Channel Application 505UDP ConfigurationUDP ConfigurationThis pop-up window is only available with EtherSAM (Y.1564)

Pop-Up Windows506 FTB-8500 Series and FTB-8120NGE/8130NGEAdvanced TOS/DSAdvanced TOS/DSEnable Differentiated ServicesAllows enabling the Differentiate

Pop-Up WindowsEthernet and Fibre Channel Application 507Advanced TOS/DSTOSNote: TOS is available when Enable Differentiated Services is not enabled.

Introducing the Smart User Interface40 FTB-8500 Series and FTB-8120NGE/8130NGEMain WindowTabsThe SUI application contains the following four main appl

Pop-Up Windows508 FTB-8500 Series and FTB-8120NGE/8130NGEPingPingThe Ping is used to determine if a network device is reachable.Note: The Ping button

Pop-Up WindowsEthernet and Fibre Channel Application 509Ping Delay (ms): Available for ping only. Enter the delay between each attempt (PING). Choice

Pop-Up Windows510 FTB-8500 Series and FTB-8120NGE/8130NGEFilter SelectionFilter SelectionThis pop-up window is only available from Traffic Analyzer -

Pop-Up WindowsEthernet and Fibre Channel Application 511Truncation CalculatorTruncation CalculatorThis pop-up window is only available from Traffic An

Pop-Up Windows512 FTB-8500 Series and FTB-8120NGE/8130NGEField Match ConfigurationField Match ConfigurationThis pop-up window is only available from T

Pop-Up WindowsEthernet and Fibre Channel Application 513Field Match ConfigurationMask: Allows masking the defined filter value. A bit mask of 1 indica

Pop-Up Windows514 FTB-8500 Series and FTB-8120NGE/8130NGETriggered Frame DetailsTriggered Frame DetailsThis pop-up window is only available from Traff

Pop-Up WindowsEthernet and Fibre Channel Application 515Data Capture ExportData Capture ExportThis pop-up window is only available from Traffic Analyz

Pop-Up Windows516 FTB-8500 Series and FTB-8120NGE/8130NGEData Capture ExportOnce generated, the capture file will be automatically opened in Wireshark

IndexIP Services Test Head 517Index-- statusExpert Mode ... 122RFC 2544 ...

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 41Main WindowFor Dual ports (RTU-310 only), see the figure below for the lo

Index518 RTU-310/310GB3... 241, 243, 248Back ... 6

IndexIP Services Test Head 519CIR... 329, 334, 497CIR %...

Index520 RTU-310/310GDest Port ... 258Destination... 178, 286, 489, 502destinatio

IndexIP Services Test Head 521Errors ... 223ES...

Index522 RTU-310/310GFilter Configuration ... 216, 220, 512Filter ... 216, 221, 512Mask...

IndexIP Services Test Head 523IIC...ixID ... 176, 4

Index524 RTU-310/310GLatency... 312Latency (RFC 2544)... 372Latenc

IndexIP Services Test Head 525Max RX Rate... 341, 343Max RX Rate L -> R ... 343M

Index526 RTU-310/310GOK... 60OOS...

IndexIP Services Test Head 527Port (BERT) ... 375Port Link...

Introducing the Smart User Interface42 FTB-8500 Series and FTB-8120NGE/8130NGEMain Window TCP Throughput Tabs on page 349RTU-310) Advanced Tab on pa

Index528 RTU-310/310GMaximum ... 236Minimum... 236Samples ...

IndexIP Services Test Head 529Stacked VLAN... 486standard...

Index530 RTU-310/310GExpert Mode - Latency (RFC 2544) ... 372Expert Mode - Throughput (RFC 2544) 366Expert Mode (BERT) ...

IndexIP Services Test Head 531Test ... 71, 129test case report ...

Index532 RTU-310/310GTX Frames ... 237TX Rate... 173T

NOTICE抩⛙CHINESE REGULATION ON RESTRICTION OF HAZARDOUS SUBSTANCES₼⦌␂ℝ☀⹂䓸德棟Ⓟ䤓屓⸩NAMES AND CONTENTS OF THE TOXIC OR HAZARDOUS SUBSTANCES OR ELEMENTS CONT

MARKING REQUIREMENTS㪖㽷尐㻑Productℶ❐Environmental protection use period (years)䘾⬒≬㔳∎䞷㦮棟 ( ㄃ )Logo㪖㉦This Exfo product㦻 EXFO ℶ❐10Batterya䟄㻯aa. If applicabl

www.EXFO.com · [email protected]/N:1062500CORPORATE HEADQUARTERS 400 Godin Avenue Quebec (Quebec) G1M 2K2 CANADATel.: 1 418 683-0211 · Fax: 1 418 683-2

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 43Main WindowIt is also possible to navigate through the help information o

Introducing the Smart User Interface44 FTB-8500 Series and FTB-8120NGE/8130NGEGlobal Test Status and ControlsGlobal Test Status and ControlsGlobal Tes

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 45Global Test Status and Controls Current status: Indicates the current al

Introducing the Smart User Interface46 FTB-8500 Series and FTB-8120NGE/8130NGEGlobal Test Status and ControlsLoadb: Loads a previously saved configura

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 47Global Test Status and ControlsDate and TimeIndicates the date (YYYY-MM-D

Contentsvi RTU-310/310G15 EtherSAM Tabs ...321Overview (Config

Introducing the Smart User Interface48 FTB-8500 Series and FTB-8120NGE/8130NGEFavoritesFavoritesFavorites gives access to 10 factory test case configu

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 49FavoritesOverwrite Selected Favorite ContentThe factory test case configu

Introducing the Smart User Interface50 FTB-8500 Series and FTB-8120NGE/8130NGETest Report GenerationTest Report GenerationClick Report from the Global

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 51Test Report Generation Report Settings: These parameters are used to ide

Introducing the Smart User Interface52 FTB-8500 Series and FTB-8120NGE/8130NGETest Report Generation Generate button: Allows generating and saving th

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 53Test Report GenerationSections Tab Pre-defined selection: Allows selecti

Introducing the Smart User Interface54 FTB-8500 Series and FTB-8120NGE/8130NGETypical Tab ElementsTypical Tab ElementsOnce the test is created, differ

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 55Typical Tab ElementsAlarm/Error MeasurementsNote: Alarms/Errors are only

Introducing the Smart User Interface56 FTB-8500 Series and FTB-8120NGE/8130NGETypical Tab ElementsTable SortingTables offer sorting capabilities on on

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 57Tab ConfigurationTab ConfigurationOnce the test is created, other tabs ne

ContentsEthernet Test Module vii21 Tools Tabs ... 407Sc

Introducing the Smart User Interface58 FTB-8500 Series and FTB-8120NGE/8130NGETab ConfigurationThis tab configuration window allows configuration of a

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 59Tab ConfigurationDefined TabsAllows the selection of a tab.Up and down ar

Introducing the Smart User Interface60 FTB-8500 Series and FTB-8120NGE/8130NGETab ConfigurationHelp Button (?)Displays the help information related to

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 61Keyboard UsageKeyboard UsageThe SUI pops up different keyboards to modify

Introducing the Smart User Interface62 FTB-8500 Series and FTB-8120NGE/8130NGEKeyboard Usage Numerical keyboards: Allows entering integer/decimal val

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 63Keyboard Usage Time Keyboard: Allows entering a time value. Date keyboa

Introducing the Smart User Interface64 FTB-8500 Series and FTB-8120NGE/8130NGEKeyboard Usage Hexadecimal keyboards: Allows entering hexadecimal value

Introducing the Smart User InterfaceEthernet and Fibre Channel Application 65Keyboard Usage Full keyboard: Allows entering numbers, letters and some

Introducing the Smart User Interface66 FTB-8500 Series and FTB-8120NGE/8130NGEKeyboard UsageITU T.50 Charactersb7 to b1 Character Description b7 to b1

Ethernet and Fibre Channel Application 675 Creating and Starting a Test CaseA test case can be created using one of the following methods: Test Setup

Contentsviii RTU-310/310GD Pop-Up Windows ...485VLAN Configuration

Creating and Starting a Test Case68 FTB-8500 Series and FTB-8120NGE/8130NGEIntroducing the Test SetupIntroducing the Test SetupThe Test Setup window i

Creating and Starting a Test CaseEthernet and Fibre Channel Application 69Introducing the Test Setup Test Setup Controls: Back returns to the previo

Creating and Starting a Test Case70 FTB-8500 Series and FTB-8120NGE/8130NGEIntroducing the Test SetupThe test path is created through the configuratio

Creating and Starting a Test CaseEthernet and Fibre Channel Application 71Introducing the Test SetupStepsAvailable withThe Test step is the root of th

Creating and Starting a Test Case72 FTB-8500 Series and FTB-8120NGE/8130NGETest Case AvailabilityTest Case AvailabilityThe remaining of this chapter d

Creating and Starting a Test CaseEthernet and Fibre Channel Application 73EtherSAM (Y.1564) Test CaseEtherSAM (Y.1564) Test CaseITU-T Y.1564 is the ne

Creating and Starting a Test Case74 FTB-8500 Series and FTB-8120NGE/8130NGEEtherSAM (Y.1564) Test CaseTo create an EtherSAM (Y.1564) test case:1. Test

Creating and Starting a Test CaseEthernet and Fibre Channel Application 75EtherSAM (Y.1564) Test Case2. Port configuration:2a. RTU-310Select the port

Creating and Starting a Test Case76 FTB-8500 Series and FTB-8120NGE/8130NGEEtherSAM (Y.1564) Test Case3. Optical configuration for Ethernet 10G interf

Creating and Starting a Test CaseEthernet and Fibre Channel Application 77EtherSAM (Y.1564) Test Case4c. Select the Frame Format. Choices are Ethernet

Certification InformationEthernet Test Module ixCertification InformationFederal Communications Commission (FCC) and Industry Canada (IC) InformationE

Creating and Starting a Test Case78 FTB-8500 Series and FTB-8120NGE/8130NGEEtherSAM (Y.1564) Test Case4g. For IPv6, click the IPv6 Config button to se

Creating and Starting a Test CaseEthernet and Fibre Channel Application 79EtherSAM (Y.1564) Test Case6. Services must be enabled before starting the t

Creating and Starting a Test Case80 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test CasesEthernet Et

Creating and Starting a Test CaseEthernet and Fibre Channel Application 81Ethernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test CasesTo create an

Creating and Starting a Test Case82 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test Cases2. Port con

Creating and Starting a Test CaseEthernet and Fibre Channel Application 83Ethernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test Cases3. Optical c

Creating and Starting a Test Case84 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test Cases4. Framing

Creating and Starting a Test CaseEthernet and Fibre Channel Application 85Ethernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test CasesCreate the t

Creating and Starting a Test Case86 FTB-8500 Series and FTB-8120NGE/8130NGEEthernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test Cases1c. From th

Creating and Starting a Test CaseEthernet and Fibre Channel Application 87Ethernet EtherSAM (Y.1564) and RFC 2544 Dual Test Set Test Cases1e. Click Sc